Backlinks to RunControl in LHCb Web

Results from LHCb web retrieved at 19:26 (GMT)

Instructions for Alignment piquets (covering VELO, Tracker, RICH, Muon, and Calo calibration) General Information and useful telephone numbers Piquet assignment...
Farm Testbed The information here follows `LHCb Farm Installation Guidlines`, LHCb XXX, E. van Herwijnen ed. These pages are meant to capture the actual state of...
Note that Roel has since prepared a new installation script for piquets https://twiki.cern.ch/twiki/bin/view/LHCb/NewMoore Installing Moore at the pit lb...
The HLT piquet guide First Steps If you are a new HLT piquet shifter, read setup instructions here. Some of the steps listed should be followed before the first shift...
HLT2 piquet guide Controlling Hlt2 Accessing LHCb2 (Hlt2 control panel) One screen next to the shift leader should show LHCb2. From remote you can login...
JRichEcConfigurator This is a Java program that manages sets of elementary cell configuration parameters for use in small lab setups or beam tests. The GUI does not...
JRichEcControl GUI This is the main DAQ control GUI and is part of the RichEcKit package. Installation General installation instructions can be found in the RichEcKit...
How to run the L0Muon online monitoring The L0Muon monitoring task which produces and publishes the histograms is L0MuonDAQMon . It is automatically launched when...
(rrom Clara) Here are some instructions on how to use LHCb1: (at the moment HLTB03 is reserved for LHCb1, so we use only this sub farm) To Run HLT1 from old deferred...
How to : setting the online DAQ This page contains the information that basic commissionners have to know to configure and run the DAQ in the calibration farm...
ParasNaik 2017 05 16 ClaireProuve 2015 07 18 Code for the Online RICH mirror alignment RICH mirror alignment project and package overview The alignment package...
ParasNaik 2017 05 16 ClaireProuve 2015 07 18 Running the Online RICH mirror alignment How to run the Alignment from the PVSS panel Before running XML file...
HLT Online Reference Guide Keywords: Setting the accept rate via PVSS,Beam Gas,Brunel output monitoring,Conditions DB snapshots,Reading Online Conditions,Event Filter...
Writing files using the runcontrol For this you need to be under dynamic allocation. Run numbers will be allocated automatically from the Rundatabase. Your files are...
HLT piquet guide: new Moore versions and TCKs There are many interdependent parts of the online system so it is important that we follow the procedures outlined on...
Running the online alignment in run 2 How to run the Alignment from the PVSS panel Open the panel from an ui or plus machine: ssh Y lbgw ssh Y ui /group...
Reference manual Chimaera2 is a readout board designed to receive binary hit data from 128 digital channels through a high density connector. The readout logic is...
This page contains information on how to configure the system and to take data in the ComLab. Columns commissioning The full test protocol is available at https:...
This page contains information on how to configure the system and to take data in the ComLab. Columns commissioning The full test protocol is available at https:...
The L0 system L0 operational info. (Pixel chip, LV) can be found here Recent L0 problems and solutions HV effects (especially ramping) often induces upsets in...
The SSB2 wiki The contents of these Wiki pages are based on the SSB2 lab manual version 0.2 that is attached to the bottom of this page. The figures have not yet been...
This page contains information on how to configure the system and to take data in the SysLab. Setup the system from scratch Switch on lbminidaq2 13. Type lspci...
This page contains information on how to configure the system and to take data in the SysLab. Setup the system from scratch Switch on lbminidaq2 13. Type lspci...
RICH 2014 Testbeam DAQ Summary and Quick Start Guide The front end data are acquired by the DBs (digital boards) that are connected to the ECs (elementary cells)...
RICH 2015 Testbeam DAQ Hardware overview The front end data are acquired by the DBs (digital boards) that are connected to the ECs (elementary cells). The DBs capture...
How to run a DAC scan Check if the firmware loaded in the PDMDBs is the one without the FIFO (go on the PDMDB panels and check if in the text fields under FPGA filename...
Test Beam for the LHCb Upgrade Silicon Tracker This page is about Test Beam for the LHCb Upgrade Silicon Tracker. The dates are scheduled in this presentation: meeting...
How to Recover the system. for most common wierd behaviours go to the bottom of these instructions. Dont Stop any pvss project. The system is now based on at least...
The one and only guide. Instructions to run the ECS/DAQ system of the testbeam setup. Important thinguies to keep in mind: 1. We run over 3 modules without...
TWeeder info for LHCb Total Number of topics: 3061 12 Topics updated during the last 7 days Days Web Topic Date S7 LHCb RealTimeAnalysisShifterChecklist...
How to find out which TCK was used for a given dataset You write a small python script like this one: from Gaudi.Configuration import from Configurables import...
Number of topics: 31

 
    • Cern Search Icon Cern Search
    • TWiki Search Icon TWiki Search
    • Google Search Icon Google Search

    LHCb All webs login

This site is powered by the TWiki collaboration platform Powered by PerlCopyright & 2008-2020 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
or Ideas, requests, problems regarding TWiki? use Discourse or Send feedback