Difference: DaVinciFAQ (1 vs. 4)

Revision 42008-06-02 - unknown

Line: 1 to 1
Changed:
<
<
Obsolete! See here
>
>

Obsolete! See LHCb/FAQ/DaVinciFAQ

 
Changed:
<
<
-- PatrickKoppenburg - 18 Jul 2007
>
>
-- PatrickKoppenburg - 02 Jun 2008

Revision 32007-07-18 - unknown

Line: 1 to 1
Changed:
<
<

Welcome to the DaVinci troubleshooting guide.

Compiled using 700 e-mails exchanged since February 2004.
>
>
Obsolete! See here
 
Changed:
<
<
This refers to DaVinci versions v9r4 (for TDR) and v11r7 or later. Some other problems may happen with older versions (like the "eta' bug") or older data (missing RICH PID). They are not listed here.
Symptom Likely cause and solution
Most common problems
$SOMEPACKROOT/options/SomeOpts.opts does not exist

DllClassManager ERROR Could not load module SomePack
$SOMEPACKROOT might not be defined
echo $SOMEPACKROOT
Whenever you change something in the requirements, or get a new package you have to do
> cmt config
in DaVinci/vXrY/cmt . Check all errors and warnings.
> source setup.csh
Quite often some old package in your newmycmt overwrites the default version of a package used by DaVinci. Do
> cmt show uses
To see who's requiring what.
> cmt sh uses produces Missing separator '/' after completion "(-l,-R,-r,-d,-o,-requirements)". In your .(t)cshrc:
set correct=cmd
instead of
set correct=all
Whenever you change something in the requirements, or get a new package you have to do

> cmt config

in DaVinci/vXrY/cmt . Check all errors and warnings.

> source setup.csh

Quite often some old package in your newmycmt overwrites the default version of a package used by DaVinci. Do

> cmt show uses

To see who's requiring what. |

DllClassManager ERROR Could not load module SomeModule

> cmt sh uses produces Missing separator '/' after completion "(-l,-R,-r,-d,-o,-requirements)".

In your .(t)cshrc: set correct=cmd instead of set correct=all

-- JuanPalacios - 24 Nov 2006

>
>
-- PatrickKoppenburg - 18 Jul 2007

Revision 22006-11-24 - JuanPalacios

Line: 1 to 1
Added:
>
>

Welcome to the DaVinci troubleshooting guide.

Compiled using 700 e-mails exchanged since February 2004.
 
Changed:
<
<
This is the FAQ page for DaVinci.
>
>
This refers to DaVinci versions v9r4 (for TDR) and v11r7 or later. Some other problems may happen with older versions (like the "eta' bug") or older data (missing RICH PID). They are not listed here.
Symptom Likely cause and solution
Most common problems
$SOMEPACKROOT/options/SomeOpts.opts does not exist

DllClassManager ERROR Could not load module SomePack
$SOMEPACKROOT might not be defined
echo $SOMEPACKROOT
Whenever you change something in the requirements, or get a new package you have to do
> cmt config
in DaVinci/vXrY/cmt . Check all errors and warnings.
> source setup.csh
Quite often some old package in your newmycmt overwrites the default version of a package used by DaVinci. Do
> cmt show uses
To see who's requiring what.
> cmt sh uses produces Missing separator '/' after completion "(-l,-R,-r,-d,-o,-requirements)". In your .(t)cshrc:
set correct=cmd
instead of
set correct=all
Whenever you change something in the requirements, or get a new package you have to do

> cmt config

in DaVinci/vXrY/cmt . Check all errors and warnings.

> source setup.csh

Quite often some old package in your newmycmt overwrites the default version of a package used by DaVinci. Do

> cmt show uses

To see who's requiring what. |

DllClassManager ERROR Could not load module SomeModule

> cmt sh uses produces Missing separator '/' after completion "(-l,-R,-r,-d,-o,-requirements)".

In your .(t)cshrc: set correct=cmd instead of set correct=all
 

-- JuanPalacios - 24 Nov 2006

Revision 12006-11-24 - JuanPalacios

Line: 1 to 1
Added:
>
>
This is the FAQ page for DaVinci.

-- JuanPalacios - 24 Nov 2006

 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright & 2008-2019 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback