Difference: VELOHighVoltageInstructionsForNewUsers (1 vs. 6)

Revision 62008-08-06 - BarinjakaRakotomiaramanana

Line: 1 to 1
 
META TOPICPARENT name="HighVoltage"
<!-- /ActionTrackerPlugin -->

Revision 52008-06-02 - StefanoDeCapua

Line: 1 to 1
 
META TOPICPARENT name="HighVoltage"
<!-- /ActionTrackerPlugin -->
Line: 24 to 24
 
  • VELOC_HV_BOARD02_LOAD.JPG:
    VELOC_HV_BOARD02_LOAD.JPG
Changed:
<
<
3) Click on the IV curve button (bottom right) to perform an I-V scan; when you select a channel to scan,
a filename is automatically suggested (look in the Write To File frame):
>
>
3) Click on the IV curve button (bottom right) to perform an I-V scan; when you select a channel to scan,
a filename is automatically suggested (look in the frame):
 
Added:
>
>
  • VELOC_HV_BOARD02_ScanFile.JPG:
    VELOC_HV_BOARD02_ScanFile.JPG
 
Changed:
<
<
4) Just replace the question marks with the proper values.
>
>
4) Just replace the question marks with the proper temperature (but check that the rest of the name is correct).
  5) Click on the ADD button to save the file name (if you don't add it, it won't be saved!). Example:
Added:
>
>
  • VELOC_HV_BOARD02_ScanFileSaved.JPG:
    VELOC_HV_BOARD02_ScanFileSaved.JPG
 6) You can also display the results of a past scan for the same slot: select the corresponding channel and then choose one of the suggested file (or browse a directory by clicking the folder icon).
Added:
>
>
  • VELOC_HV_BOARD02_ScanPastFile.JPG:
    VELOC_HV_BOARD02_ScanPastFile.JPG
 7) Select the next channel to scan and repeat point (4), (5) and (6).

8) Push the START button to perform the scan.

Changed:
<
<
9) Once the IV scan has been done, close the panel and go back to the Board Panel; switch on the enabled channels by sending the command Go_STANDBY1 (=10 V) or Go_STANDBY2 (=50 V) or Go_READY(=100 V) from the top button. See for example the figures below:

  • VELOC_HV_BOARD02_Go_Ready.JPG:
    VELOC_HV_BOARD02_Go_Ready.JPG
>
>
9) Once the IV scan has been done, close the panel and go back to the Board Panel; switch on the enabled channels by sending the command Go_STANDBY1 (=10 V) or Go_STANDBY2 (=50 V) or Go_READY(=100 V) from the top button. See for example the figures below:
 
Changed:
<
<
Wait that all the enabled units are in the requested state. Example:
>
>
  • VELOC_HV_BOARD02_Send_Go_Ready.JPG:
    VELOC_HV_BOARD02_Send_Go_Ready.JPG
 
  • VELOC_HV_BOARD02_Ready.JPG:
    VELOC_HV_BOARD02_Ready.JPG
Line: 52 to 57
 -- StefanoDeCapua - 14 May 2008

META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Ready.JPG" attr="" comment="" date="1210780314" name="VELOC_HV_BOARD02_Ready.JPG" path="VELOC_HV_BOARD02_Ready.JPG" size="105332" stream="VELOC_HV_BOARD02_Ready.JPG" user="Main.StefanoDeCapua" version="1"
Deleted:
<
<
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Go_Ready.JPG" attr="" comment="" date="1210780294" name="VELOC_HV_BOARD02_Go_Ready.JPG" path="VELOC_HV_BOARD02_Go_Ready.JPG" size="106679" stream="VELOC_HV_BOARD02_Go_Ready.JPG" user="Main.StefanoDeCapua" version="1"
 
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_LOAD.JPG" attr="" comment="" date="1210779362" name="VELOC_HV_BOARD02_LOAD.JPG" path="VELOC_HV_BOARD02_LOAD.JPG" size="106334" stream="VELOC_HV_BOARD02_LOAD.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="TopLevel.JPG" attr="" comment="" date="1210770634" name="TopLevel.JPG" path="TopLevel.JPG" size="24192" stream="TopLevel.JPG" user="Main.StefanoDeCapua" version="2"
META FILEATTACHMENT attachment="VELOC_HV.JPG" attr="" comment="" date="1210771107" name="VELOC_HV.JPG" path="VELOC_HV.JPG" size="136024" stream="VELOC_HV.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_OFF.JPG" attr="" comment="" date="1210777764" name="VELOC_HV_BOARD02_OFF.JPG" path="VELOC_HV_BOARD02_OFF.JPG" size="105046" stream="VELOC_HV_BOARD02_OFF.JPG" user="Main.StefanoDeCapua" version="1"
Added:
>
>
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_ScanFile.JPG" attr="" comment="" date="1212393497" name="VELOC_HV_BOARD02_ScanFile.JPG" path="VELOC_HV_BOARD02_ScanFile.JPG" size="126383" stream="VELOC_HV_BOARD02_ScanFile.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_ScanFileSaved.JPG" attr="" comment="" date="1212393632" name="VELOC_HV_BOARD02_ScanFileSaved.JPG" path="VELOC_HV_BOARD02_ScanFileSaved.JPG" size="128369" stream="VELOC_HV_BOARD02_ScanFileSaved.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_ScanPastFile.JPG" attr="" comment="" date="1212393957" name="VELOC_HV_BOARD02_ScanPastFile.JPG" path="VELOC_HV_BOARD02_ScanPastFile.JPG" size="130467" stream="VELOC_HV_BOARD02_ScanPastFile.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Send_Go_Ready.JPG" attr="" comment="" date="1212394343" name="VELOC_HV_BOARD02_Send_Go_Ready.JPG" path="VELOC_HV_BOARD02_Send_Go_Ready.JPG" size="112937" stream="VELOC_HV_BOARD02_Send_Go_Ready.JPG" user="Main.StefanoDeCapua" version="1"

Revision 42008-06-01 - StefanoDeCapua

Line: 1 to 1
 
META TOPICPARENT name="HighVoltage"
<!-- /ActionTrackerPlugin -->
Line: 6 to 6
  1) Open a main HV overview panel by right-clicking VELOA(C)_HV:
Changed:
<
<
TopLevel.JPG
>
>
  • TopLevel.JPG:
    TopLevel.JPG
 
Changed:
<
<
This brings up the VELOA(C)_HV overview screen:
>
>
This brings up the VELOA(C)_HV overview screen. This panel describes the overall status of the A(C) side HV system.
 
Changed:
<
<
VELOC_HV.JPG
>
>
  • VELOC_HV.JPG:
    VELOC_HV.JPG
 
Changed:
<
<
This panel describes the overall status of the A(C) side HV system.

2) Double-click on the HV board you want to operate to get the corresponding
PVSS panel; enable only the channels to be used and the Configuration Database (ConfDB).
>
>
2) Double-click on the HV board you want to operate to get the corresponding
PVSS panel; enable only the channels to be used and the Configuration Database (ConfDB).
 
Changed:
<
<
VELOC_HV_BOARD02_OFF.JPG
>
>
  • VELOC_HV_BOARD02_OFF.JPG:
    VELOC_HV_BOARD02_OFF.JPG
  If the ConfDB is in state "NOT_READY", please LOAD it:
Changed:
<
<
VELOC_HV_BOARD02_LOAD.JPG
>
>
  • VELOC_HV_BOARD02_LOAD.JPG:
    VELOC_HV_BOARD02_LOAD.JPG
  3) Click on the IV curve button (bottom right) to perform an I-V scan; when you select a channel to scan,
a filename is automatically suggested (look in the Write To File frame):
Deleted:
<
<
VELOC_HV_BOARD02_Scan.JPG
  4) Just replace the question marks with the proper values.

5) Click on the ADD button to save the file name (if you don't add it, it won't be saved!). Example:

Changed:
<
<
VELOC_HV_BOARD02_Scan_File.JPG
>
>
6) You can also display the results of a past scan for the same slot: select the corresponding channel and then choose one of the suggested file (or browse a directory by clicking the folder icon).
 
Changed:
<
<
6) Select the next channel to scan and repeat point (4) and (5)
>
>
7) Select the next channel to scan and repeat point (4), (5) and (6).
 
Changed:
<
<
7) Push the START button to perform the scan.
>
>
8) Push the START button to perform the scan.
 
Changed:
<
<
8) Once the IV scan has been done, close the panel and go back to the Board Panel; switch on the enabled channel
one by one sending the command Go_STANDBY1 (=10 V) or Go_STANDBY2 (=50 V) or Go_READY(=100 V).
See for example the figures below:
>
>
9) Once the IV scan has been done, close the panel and go back to the Board Panel; switch on the enabled channels by sending the command Go_STANDBY1 (=10 V) or Go_STANDBY2 (=50 V) or Go_READY(=100 V) from the top button. See for example the figures below:
 
Changed:
<
<
VELOC_HV_BOARD02_Go_Ready.JPG
>
>
  • VELOC_HV_BOARD02_Go_Ready.JPG:
    VELOC_HV_BOARD02_Go_Ready.JPG
 
Changed:
<
<
VELOC_HV_BOARD02_Ready.JPG
>
>
Wait that all the enabled units are in the requested state. Example:
 
Changed:
<
<
-- StefanoDeCapua - 14 May 2008
>
>
  • VELOC_HV_BOARD02_Ready.JPG:
    VELOC_HV_BOARD02_Ready.JPG
 
Changed:
<
<
  • TopLevel.JPG:
    TopLevel.JPG
>
>
-- StefanoDeCapua - 14 May 2008
 
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Ready.JPG" attr="" comment="" date="1210780314" name="VELOC_HV_BOARD02_Ready.JPG" path="VELOC_HV_BOARD02_Ready.JPG" size="105332" stream="VELOC_HV_BOARD02_Ready.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Go_Ready.JPG" attr="" comment="" date="1210780294" name="VELOC_HV_BOARD02_Go_Ready.JPG" path="VELOC_HV_BOARD02_Go_Ready.JPG" size="106679" stream="VELOC_HV_BOARD02_Go_Ready.JPG" user="Main.StefanoDeCapua" version="1"
Line: 51 to 57
 
META FILEATTACHMENT attachment="TopLevel.JPG" attr="" comment="" date="1210770634" name="TopLevel.JPG" path="TopLevel.JPG" size="24192" stream="TopLevel.JPG" user="Main.StefanoDeCapua" version="2"
META FILEATTACHMENT attachment="VELOC_HV.JPG" attr="" comment="" date="1210771107" name="VELOC_HV.JPG" path="VELOC_HV.JPG" size="136024" stream="VELOC_HV.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_OFF.JPG" attr="" comment="" date="1210777764" name="VELOC_HV_BOARD02_OFF.JPG" path="VELOC_HV_BOARD02_OFF.JPG" size="105046" stream="VELOC_HV_BOARD02_OFF.JPG" user="Main.StefanoDeCapua" version="1"
Deleted:
<
<
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Scan.JPG" attr="" comment="" date="1210779469" name="VELOC_HV_BOARD02_Scan.JPG" path="VELOC_HV_BOARD02_Scan.JPG" size="76682" stream="VELOC_HV_BOARD02_Scan.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Scan_File.JPG" attr="" comment="" date="1210779594" name="VELOC_HV_BOARD02_Scan_File.JPG" path="VELOC_HV_BOARD02_Scan_File.JPG" size="78918" stream="VELOC_HV_BOARD02_Scan_File.JPG" user="Main.StefanoDeCapua" version="1"

Revision 32008-05-15 - StefanoDeCapua

Line: 1 to 1
 
META TOPICPARENT name="HighVoltage"
<!-- /ActionTrackerPlugin -->
Line: 42 to 42
  -- StefanoDeCapua - 14 May 2008
Added:
>
>
  • TopLevel.JPG:
    TopLevel.JPG
 
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Ready.JPG" attr="" comment="" date="1210780314" name="VELOC_HV_BOARD02_Ready.JPG" path="VELOC_HV_BOARD02_Ready.JPG" size="105332" stream="VELOC_HV_BOARD02_Ready.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Go_Ready.JPG" attr="" comment="" date="1210780294" name="VELOC_HV_BOARD02_Go_Ready.JPG" path="VELOC_HV_BOARD02_Go_Ready.JPG" size="106679" stream="VELOC_HV_BOARD02_Go_Ready.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_LOAD.JPG" attr="" comment="" date="1210779362" name="VELOC_HV_BOARD02_LOAD.JPG" path="VELOC_HV_BOARD02_LOAD.JPG" size="106334" stream="VELOC_HV_BOARD02_LOAD.JPG" user="Main.StefanoDeCapua" version="1"

Revision 22008-05-14 - StefanoDeCapua

Line: 1 to 1
 
META TOPICPARENT name="HighVoltage"
Added:
>
>
<!-- /ActionTrackerPlugin -->
 Instructions for New Users to use the VELO HV setting tools
Changed:
<
<
First open a main HV overview panel by right-clicking VELOA(C)_HV:
>
>
1) Open a main HV overview panel by right-clicking VELOA(C)_HV:
  TopLevel.JPG

This brings up the VELOA(C)_HV overview screen:

Changed:
<
<
VELOC_HV.JPG
>
>
VELOC_HV.JPG

This panel describes the overall status of the A(C) side HV system.

2) Double-click on the HV board you want to operate to get the corresponding
PVSS panel; enable only the channels to be used and the Configuration Database (ConfDB).

VELOC_HV_BOARD02_OFF.JPG

If the ConfDB is in state "NOT_READY", please LOAD it:

VELOC_HV_BOARD02_LOAD.JPG

3) Click on the IV curve button (bottom right) to perform an I-V scan; when you select a channel to scan,
a filename is automatically suggested (look in the Write To File frame):

VELOC_HV_BOARD02_Scan.JPG

4) Just replace the question marks with the proper values.

5) Click on the ADD button to save the file name (if you don't add it, it won't be saved!). Example:

VELOC_HV_BOARD02_Scan_File.JPG

6) Select the next channel to scan and repeat point (4) and (5)

7) Push the START button to perform the scan.

8) Once the IV scan has been done, close the panel and go back to the Board Panel; switch on the enabled channel
one by one sending the command Go_STANDBY1 (=10 V) or Go_STANDBY2 (=50 V) or Go_READY(=100 V).
See for example the figures below:

 
Changed:
<
<
This panel describes the overall status of the A(C) side HV system: on the left you find
the sub-systems
>
>
VELOC_HV_BOARD02_Go_Ready.JPG
 
Changed:
<
<

Double-click on the
>
>
VELOC_HV_BOARD02_Ready.JPG
  -- StefanoDeCapua - 14 May 2008
Added:
>
>
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Ready.JPG" attr="" comment="" date="1210780314" name="VELOC_HV_BOARD02_Ready.JPG" path="VELOC_HV_BOARD02_Ready.JPG" size="105332" stream="VELOC_HV_BOARD02_Ready.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Go_Ready.JPG" attr="" comment="" date="1210780294" name="VELOC_HV_BOARD02_Go_Ready.JPG" path="VELOC_HV_BOARD02_Go_Ready.JPG" size="106679" stream="VELOC_HV_BOARD02_Go_Ready.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_LOAD.JPG" attr="" comment="" date="1210779362" name="VELOC_HV_BOARD02_LOAD.JPG" path="VELOC_HV_BOARD02_LOAD.JPG" size="106334" stream="VELOC_HV_BOARD02_LOAD.JPG" user="Main.StefanoDeCapua" version="1"
 
META FILEATTACHMENT attachment="TopLevel.JPG" attr="" comment="" date="1210770634" name="TopLevel.JPG" path="TopLevel.JPG" size="24192" stream="TopLevel.JPG" user="Main.StefanoDeCapua" version="2"
META FILEATTACHMENT attachment="VELOC_HV.JPG" attr="" comment="" date="1210771107" name="VELOC_HV.JPG" path="VELOC_HV.JPG" size="136024" stream="VELOC_HV.JPG" user="Main.StefanoDeCapua" version="1"
Added:
>
>
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_OFF.JPG" attr="" comment="" date="1210777764" name="VELOC_HV_BOARD02_OFF.JPG" path="VELOC_HV_BOARD02_OFF.JPG" size="105046" stream="VELOC_HV_BOARD02_OFF.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Scan.JPG" attr="" comment="" date="1210779469" name="VELOC_HV_BOARD02_Scan.JPG" path="VELOC_HV_BOARD02_Scan.JPG" size="76682" stream="VELOC_HV_BOARD02_Scan.JPG" user="Main.StefanoDeCapua" version="1"
META FILEATTACHMENT attachment="VELOC_HV_BOARD02_Scan_File.JPG" attr="" comment="" date="1210779594" name="VELOC_HV_BOARD02_Scan_File.JPG" path="VELOC_HV_BOARD02_Scan_File.JPG" size="78918" stream="VELOC_HV_BOARD02_Scan_File.JPG" user="Main.StefanoDeCapua" version="1"

Revision 12008-05-14 - StefanoDeCapua

Line: 1 to 1
Added:
>
>
META TOPICPARENT name="HighVoltage"
Instructions for New Users to use the VELO HV setting tools

First open a main HV overview panel by right-clicking VELOA(C)_HV:

TopLevel.JPG

This brings up the VELOA(C)_HV overview screen:

VELOC_HV.JPG

This panel describes the overall status of the A(C) side HV system: on the left you find
the sub-systems


Double-click on the

-- StefanoDeCapua - 14 May 2008

META FILEATTACHMENT attachment="TopLevel.JPG" attr="" comment="" date="1210770634" name="TopLevel.JPG" path="TopLevel.JPG" size="24192" stream="TopLevel.JPG" user="Main.StefanoDeCapua" version="2"
META FILEATTACHMENT attachment="VELOC_HV.JPG" attr="" comment="" date="1210771107" name="VELOC_HV.JPG" path="VELOC_HV.JPG" size="136024" stream="VELOC_HV.JPG" user="Main.StefanoDeCapua" version="1"
 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright & 2008-2019 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback