Remote connection to control PC

The SMC chiller is connected to a small form-factor control PC (pc-unige-irrad) running Windows 10. In order to connect to the control PC in b161 you must first connect to the Windows TS and from there to the control PC. Passing through the TS is required to be able to login in the control PC using a local account.

1.- Open a remote desktop connection to the CERN Windows Terminal Server (TS):

  • connect to cernts.cern.ch
  • user: cern\guest
  • password: your password

The recommended client software is Microsoft Remote Desktop client, which is available for both Windows and Mac OS. For linux one can use "VNC viewer" or XfreeRDP clients. For additional information please check https://cern.service-now.com/service-portal?id=kb_article&n=KB0006557.

2.- once connected to cernts.cern.ch, open a new connection to pc-unige-irrad.cern.ch:

  • user: pc-unige-irrad\faser
  • password: password for local account in the windows control PC

Screenshot_RD.png

Remote operation of SMC chiller

Enabling remote operation

When operating the chiller manually via the front panel it is said to be in LOCAL mode. To enable remote operation the chiller has to be put in SERIAL communication mode.

SERIAL mode can be enabled as follows:

  1. press and hold the [MENU] key for 2 secs. The digital display should show a new menu code. Repeat press and hold [MENU] for 2 secs until the communication setting screen (labelled as Co.01) appears in the display.
  2. select Ser with the [up] and [down] arrow-keys, then press [SEL] key to confirm. This sets serial communication mode.
  3. in the next sub-menu (labelled as Co.02) select ndbS corresponding to the MODBUS protocol. Confirm by pressing the [SEL] key.
  4. in the next sub-menu (labelled as Co.03) select 232C corresponding to RS-232C standard. Confirm by pressing the [SEL] key.
  5. keep pressing [SEL] key until sub-menu Co.05 is displayed. Select address 1 and confirm by pressing the [SEL] key.
  6. in the next sub-menu (labelled as Co.06) select 9.6 corresponding to 9600 bps rate. Confirm by pressing the [SEL] key.
  7. exit by pressing the [MENU] key.

To return to LOCAL mode, repeat steps 1 and 2 and select Loc in the Co.01 menu.

For more information read chapter 4 of the SMC Communication manual.

LabVIEW application

A LabVIEW (2019) application has been created to control the SMC chiller in b161. The chiller is connected to the PC via a USB-RS232 cable with a FTDI chip. The driver chosen is Virtual Com Port so that to make it easier its control in LabVIEW using standard VISA vis. The alias SMC is defined in NI MAX to the corresponding COM port of the VCP. If the chiller is correctly configured in SERIAL mode with MODBUS protocol as explained above, upon start of the LabVIEW application the proper serial port is initialized and the contents of the different registers are automatically monitored every 3 seconds. The figure below shows a screenshot of the main program.

chiller-smc-lv.png

The controls and indicators shown in the front-panel are explained below.

  • Controls
    • Stop prog control button: stops the main application, closes the VISA device session.
    • Start / stop chiller control: allows to start (run mode) or stop the chiller.
    • Set temperature control button: sends a command to set a new target temperature. The new value is reflected in the SV display of the chiller front-panel.
  • Indicators
    • Status boolean indicator: shows if the chiller is running or stopped.
    • Alarm boolean indicator: shows if any bit of the different alarm registers is set.
    • Current temperature indicator: shows the current fluid temperature (also shown in the PV display of the chiller front-panel).
    • Target temperature indicator: shows the target set point (i.e. the temperature the chiller is trying to reach).
    • Status1, Alarm1, Alarm2 and Alarm3 boolean array indicators: show the bit content of the corresponding 16-bit registers (bit 0 is shown left-most, bit 15 right-most). Refer to sections 4.10.4 and 4.10.5 of the SMC Communication manual for the meaning of the single bits.
    • HeartBeat boolean indicator: it blinks every time the registers are monitored. This is just a visual help to be sure the automatic monitoring is running.

Note the user can only act on the controls.

Additional information

-- SergioGonzalez - 2020-05-22

Topic attachments
I Attachment History Action Size DateSorted ascending Who Comment
PDFpdf HRX-OM-M091.pdf r1 manage 2516.2 K 2020-05-22 - 11:11 SergioGonzalez SMC Communication manual
PDFpdf HRX-OM-R016-K.pdf r1 manage 5828.4 K 2020-05-22 - 11:10 SergioGonzalez SMC Operation Manual
PNGpng chiller-smc-lv.png r1 manage 23.4 K 2020-05-22 - 11:35 SergioGonzalez SMC LabVIEW front-panel
PNGpng Screenshot_RD.png r1 manage 483.7 K 2020-05-26 - 17:50 SergioGonzalez Screenshot RD
Edit | Attach | Watch | Print version | History: r3 < r2 < r1 | Backlinks | Raw View | WYSIWYG | More topic actions
Topic revision: r3 - 2020-05-26 - SergioGonzalez
 
    • Cern Search Icon Cern Search
    • TWiki Search Icon TWiki Search
    • Google Search Icon Google Search

    FASER All webs login

This site is powered by the TWiki collaboration platform Powered by PerlCopyright & 2008-2020 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback