Installation of a gLite WMS or LCG RB node

Request of a new host certificate

The general procedure can be found here (GD specific) and here (FIO specific). To be short, you have to execute the following command line (the certificate is automatically uploaded to SINDES):

/usr/bin/host-certificate-manager --from=it-dep-gd-gmod.cern.ch --username=gdadmin HOSTNAME *(without .cern.ch !!!)*

Register the node to the myproxy server

Send an email to CCService.ManagerOnDuty@cernNOSPAMPLEASE.ch to request the add of the hosts to the myproxy server. You must give the DN of the machine.

Configuration of the 3 RAID-1 disks on a mid-range server

• Check that the 3 RAID-1 disks are configured:

                [root@rb113 root]# tw_cli /c0 show

                Unit  UnitType  Status         %Cmpl  Stripe  Size(GB)  Cache  AVerify  IgnECC
                ------------------------------------------------------------------------------
                u0    RAID-1    OK             -      -       149.001   ON     OFF      OFF      
                u1    RAID-1    OK             -      -       232.82    ON     OFF      OFF      
                u2    RAID-1    OK             -      -       232.82    ON     OFF      OFF      
                u3    RAID-1    OK             -      -       232.82    ON     OFF      OFF      

                Port   Status           Unit   Size        Blocks        Serial
                ---------------------------------------------------------------
                p0     OK               u0     153.38 GB   321672960     VDK91GTE0ABPKR
                p1     OK               u0     153.38 GB   321672960     VDK91GTE0B7K9R
                p2     OK               u1     232.88 GB   488397168     VDS41DT4F5LDMJ
                p3     OK               u1     232.88 GB   488397168     VDS41DT4F4M22J
                p4     OK               u2     232.88 GB   488397168     VDS41DT4F5K9GJ
                p5     OK               u2     232.88 GB   488397168     VDS41DT4F5JNDJ
                p6     OK               u3     232.88 GB   488397168     VDS41DT4F571KJ
                p7     OK               u3     232.88 GB   488397168     VDS41DT4F5LDZJ

                Name  OnlineState  BBUReady  Status    Volt     Temp     Hours  LastCapTest
                ---------------------------------------------------------------------------
                bbu   On           Yes       OK        OK       OK       0      xx-xxx-xxxx

• Creation of the RAID-1 partitions

                tw_cli /c0 add type=raid1 disk=2:3
                tw_cli /c0 add type=raid1 disk=4:5
                tw_cli /c0 add type=raid1 disk=6:7

• Deletion of the RAID-1 partitions

                tw_cli /c0/u1 del
                tw_cli /c0/u2 del
                tw_cli /c0/u3 del

• Copy script file /usr/local/sbin/fileserver-datadisk-setup.sh in /root, edit it and change the value 262144 to 8192 (it corresponds to the bytes-per-inode value). The former value was too high, and value 4092 is too small.

• Get this script fileserver-datadisk-setup.sh and execute it to the target node. Check first that the bytes-per-inode value has been changed from 262144 to 8192.

                [root@rb113 root]# ./fileserver-datadisk-setup.sh --prefix /data --fs ext3 
                Searching for accessible SCSI devices:
                    /dev/sdb
                    /dev/sdc
                    /dev/sdd
                Scanning for RAID superblocks on SCSI devices:
                    /dev/sdb: none
                    /dev/sdc: none
                    /dev/sdd: none
                Setting up /dev/sdb:
                    fdisk /dev/sdb > /tmp/fdisk.sdb.log 2>&1
                    dd if=/dev/zero of=/dev/sdb1 bs=1M count=8 2>/dev/null
                    mkfs.ext2 -m 0 -i 8192 /dev/sdb1 >/tmp/mkfs.sdb1.log 2>&1
                    # Changing filesystem label: '' -> 'data01'
                    tune2fs -L data01 /dev/sdb1 > /tmp/tune2fs.sdb1.log
                    tune2fs -j /dev/sdb1 >> /tmp/tune2fs.sdb1.log
                    # mount point exists
                    print 'LABEL=data01 /data01 ext3    defaults        1 3' >> /etc/fstab
                    mount -t ext3 /dev/sdb1 /data01
                Setting up /dev/sdc:
                    fdisk /dev/sdc > /tmp/fdisk.sdc.log 2>&1
                    dd if=/dev/zero of=/dev/sdc1 bs=1M count=8 2>/dev/null
                    mkfs.ext2 -m 0 -i 8192 /dev/sdc1 >/tmp/mkfs.sdc1.log 2>&1
                    # Changing filesystem label: '' -> 'data02'
                    tune2fs -L data02 /dev/sdc1 > /tmp/tune2fs.sdc1.log
                    tune2fs -j /dev/sdc1 >> /tmp/tune2fs.sdc1.log
                    # mount point exists
                    print 'LABEL=data02 /data02 ext3    defaults        1 3' >> /etc/fstab
                    mount -t ext3 /dev/sdc1 /data02
                Setting up /dev/sdd:
                    fdisk /dev/sdd > /tmp/fdisk.sdd.log 2>&1
                    dd if=/dev/zero of=/dev/sdd1 bs=1M count=8 2>/dev/null
                    mkfs.ext2 -m 0 -i 8192 /dev/sdd1 >/tmp/mkfs.sdd1.log 2>&1
                    # Changing filesystem label: '' -> 'data03'
                    tune2fs -L data03 /dev/sdd1 > /tmp/tune2fs.sdd1.log
                    tune2fs -j /dev/sdd1 >> /tmp/tune2fs.sdd1.log
                    # mount point exists
                    print 'LABEL=data03 /data03 ext3    defaults        1 3' >> /etc/fstab
                    mount -t ext3 /dev/sdd1 /data03

gLite WMS specific things to do

• Run the [[][WMS-post-install] script used to migrate the middleware log files, sandbox and MySQL database on the 3 RAID-1 partitions

LCG RB specific things to do

• Run the [[][RB-post-install] script used to migrate the middleware log files, sandbox and MySQL database on the 3 RAID-1 partitions