Lustre Server Setup

I created a ~46TB Lustre file system on 25 disk servers. Lustre Version is 1.6.4.2 using official RPMS from lustre.org.
On every disk server there is a 2TB file created in /shift/xns/lustre/ which is formatted with mkfs.lustre and then mounted via a loopback device.
On the headnode I have created an 8GB MDS file system inside the /pool directory which is also mounted as an MDS via a loopback device.
dd if=/dev/zero of=/pool/lustremds bs=1000 count=0 seek=8589934592

mkfs.lustre --fsname=tier2fs --mdt --mgs --backfstype=ldiskfs --device-size=8000000 --reformat /pool/lustremds
mkdir /mdt
mount -o loop -t lustre /pool/lustremds /mdt/

wassh -l root -e "lxb8971" -c fileserver/dpm-test "mkdir -p /shift/xns/lustre/"


wassh -l root -e "lxb8971" -c fileserver/dpm-test "dd if=/dev/zero of=/shift/xns/lustre/2TB bs=1024 count=0 seek=2000000000"
wassh -l root -e "lxb8971" -c fileserver/dpm-test "mkfs.lustre --fsname tier2fs --ost --mgsnode=lxb8971@tcp0 --backfstype=ldiskfs --device-size=2000000000 --reformat /shift/xns/lustre/2TB"
############################################################################################################
# if you want an EIOE in case an OST goes down add -param="failover.mode=failout" to the arguments above!!!!
############################################################################################################
wassh -l root -e "lxb8971" -c fileserver/dpm-test "mkdir -p /ost0"
wassh -l root -e "lxb8971" -c fileserver/dpm-test "mount -t lustre -o loop /shift/xns/lustre/2TB /ost0/"

# to mount the filesystem on a client machine do
mkdir /tier2fs
mount -t lustre -o user_xattr,acl lxb8971.cern.ch:/tier2fs /tier2fs

Lustre Client Setup

I have setup the clients lxb8901-8930. They run the default CERN kernel and I recompiled Lustre with the CERN kernel on each machine.
Unpack the sources or use source rpm:
./configure --with-linux=/usr/src/kernels/2.6.9-67.0.1.EL.cern-smp-x86_64/
make
make install

The LustreFS /tier2fs is mounted like:
wassh -l root "mkdir /tier2fs; depmod; modprobe lustre"
wasss -l root -h lxb89[01-30] "mount -t lustre -o user_xattr,acl lxb8971.cern.ch:/tier2fs /tier2fs

Trivial tests

File creation (filesize 8 bytes) from a standard CERN desktop (100Mbit). 250 files/s. File creation on one of the disk server 760 files/s.
Copy of a 1 GB file from a neighbour disk server 18s. Copy of a 1 GB from the disk server which has a file locally (via the mounted directory): 10s.
General observation: Directory listing with 'ls' is relatively slow for directories with many entires (> O(1000) ). A 'find' command gives very fast results even for thousands of files.


'ldiskfs'

ldiskfs allows to mount the lustre device like a normal FS with the lustre interal fs structure visible. The same works on the MDS node which stores file meta data. 'getfattr' allows to dump all the meta data information and can be used
to make a backup of a lustre MDS.

mount -t ldiskfs -o loop /shift/xns/lustre/2TB /mnt/lustre
[root@lxfsrd4005 tier2fs]# ls -la /mnt/lustre/
total 52
drwxr-xr-x  5 root root  4096 Mar  3 18:56 .
drwxr-xr-x  3 root root  4096 Mar  3 22:42 ..
-rwx------  1 root root    32 Mar  3 18:56 CATALOGS
drwxr-xr-x  2 root root  4096 Mar  3 19:38 CONFIGS
drwx------  5 root root  4096 Mar  3 18:56 O
-rw-r--r--  1 root root  4096 Mar  3 18:56 health_check

-rwx------  1 root root  8704 Mar  3 18:56 last_rcvd
drwx------  2 root root 16384 Mar  3 18:54 lost+found

Possible integration of xrootd/gridftp into Lustre FS

The lustre api allows to retrieve the file layout for each lustre entry on the MDS. This information can be used f.e. by an xrootd redirector to direct a client to the disk server which stores a certain file. On this disk server the
file could simply be opened using the mounted FS but it would be a sort of local access via local network. Alternatively one could mount on each disk server the OST with ldiskfs and access directly the file without using the lustre device. For striped files one would need to extend the xrootd client or issue ENOTSUP.
A Lustre FS could be run without any authentication and it would be mountable only by dedicated hosts while (grid-) jobs would access the files via a remote protocol doing usual GSI authentication.
Main requirement would be a clear mapping from DN (or kerberos principals) to real UID/GID pairs. An xrootd plugin for simple read/write should be doable in few days.
If SRM is still wanted, StORM could be tried as SRM interface.


Lustre and Quota

Quota can be set per user or per group. If group quota exists on a filesystem it supersedes the user quota.
Quota is set for the complete filesyste - not for individual directories.
Enable quota on a file system:
lfs quotacheck -ug /tier2fs
Set quota for the user 'xprod':
lfs setquota -u xprod 3000000 3200000 10000 12000 /tier2fs/
This sets around 3 GB soft and 3.2 GB hardquota. 10000 inodes soft and 12000 inodes hard quota. By default quota is reserved in chunks of 100 Mb, so you have to specify atleast <X>=100 x <number of disk servers/OSTs>, otherwise you see very strange effects and quota does not work properly.
To list quota do:
lfs quota -u xprod
I did a very simple test exceeding the quota and a file copy stops when the quota is reached and '1' is returned in the shell. The uncomplete file stays in the file system.
One can also set a grace limit for quota:
lfs setquota -t 100 2000 /tier2fs
100 is the block grace, 2000 the inode grace.

Lustre Tests

Single Client Machine Writes

One must distinguish here cached and non-cached writes. Every write test starts with very high performance until the write cache is exhausted and the cache has to be commited.
Running a test with 100 clients writing 2000 files each the performance goes asymtotically towards 40 files/s = 40 Mb/s.

File Deletion


The Deletion of 1.6 Mio files (8 TB) took 27m35s executed via 'rm -r ...' from a single clients (~1000 files/s).

Disk Server Hotspots


In a test where I read with 3000 clients ( 30 mounting clients running 100 parallel copies each) 0.5 Gb files the FS created a hostspot disk server - e.g. after some stable running one disk server accumulated the requests of all clients. Once the equilibrium is broken we enter a vicious circle. If
file streaming of large files is desired on a Lustre FS the product of <N clients> * <file stripe size> has to be in a healthy ratio to the i/o output of a single disk server. If many clients will do streaming the solution is to use more than one
stripe per file. The maximum number of stripes for lustre is 160. On the contrary a single disk server failure will do a bigger damage to the file availability.

Lustre FS Hangs

If one of the disk server/OSTs crashes in a default setup the complete FS get's blocked. During a write test 1 disk server crashed for still unknown reason. As a result all 3000 copy processes stop in status 'D' and the filesystem blocks.
The situation can be solved either
a) reboot the disk server asap (I couldn't do that)
b) - identify the hanging server (look for a LustreError with dmsg on the MDS and get the OST name) - useful is also
 cat /proc/fs/lustre/osc/*/ost_server_uuid | less
- get the device ID with 'lctl dl'
- deactive the device with 'lctl --device <id> deactivate'
- one has to deactivate the device on the MDS and on ALL clients !!!!

If one does not want blocking in case of a OST failure and prefers to see EIO on clients, the OSTs should be created with the '--failover' option or with tunefs:
tunefs.lustre --writeconf --param="failover.mode=failout" <device>
. On the contrary the blocking has the advantage that one can fix the problem and all processes and pending transactions will continue once the failed OST came back.
Another useful option to set on the OSTs is:
 lctl -w lnet.panic_on_lbug=1
 lctl -w kernel.panic_on_oops
This enables automatic reboot of the machine whenever a bug is hit in the lustre kernel or the kernel itself and reduces the downtime caused by an OST failure.

Lustre Write Test 29 client machines ( 10 cp's a 50 Mb write)


lustrewrite50.gif

The tests runs for ~120 Minutes. We write at a rate of max(2.6. GB/s -> we have 25 disk server and 30 client machines). We write 290000 x 50 Mb files (14 Tb) without any error.
The distribution of the time to write a file shows the effect of the caching in the client. If the cache is empty the write is much faster than the average of 5.745s. If the cache is full the write
has to wait longer until the cache is empty and produces atleast part of the tail. The missing 18 entries in the histogram got lost during the script processing of the logfiles.

lustrewrite50.jpg

Lustre Read Tests

Bonnie Performance on a disk server:

[root@lxfsrd4005 ext3]# /root/Bonnie -s 16000
File './Bonnie.30795', size: 16777216000
Writing with putc()...
[root@lxfsrd4005 ext3]# /root/Bonnie -s 32000
File './Bonnie.30804', size: 33554432000
Writing with putc()...done
Rewriting...done
Writing intelligently...done
Reading with getc()...done
Reading intelligently...done
Seeker 1...Seeker 2...Seeker 3...start 'em...done...done...done...
              -------Sequential Output-------- ---Sequential Input-- --Random--
              -Per Char- --Block--- -Rewrite-- -Per Char- --Block--- --Seeks---
Machine    MB K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU  /sec %CPU
         32000 60691 98.9 268856 84.2 74771 21.1 59208 96.2 158751 15.3  77.9  0.3

I found that during the following tests two disk server were doing a 'verify' operation after reboot. This servers were influencing the overall performance of the tests evidently since on the clients there were slow copy processes on this 2 disk servers present all the time.

lxfsrc1201:

   Unit  UnitType  Status         %RCmpl  %V/I/M  Stripe  Size(GB)  Cache  AVrfy
   ------------------------------------------------------------------------------
   u0    RAID-1    OK             -       -       -       232.82    ON     OFF
   u1    RAID-10   VERIFYING      -       98      64K     4656.51   ON     OFF
   u2    SPARE     OK             -       -       -       465.753   -      OFF
   u3    SPARE     OK             -       -       -       465.753   -      OFF
   Unit  UnitType  Status         %RCmpl  %V/I/M  Stripe  Size(GB)  Cache  AVrfy

lxfsrc1203:
   ------------------------------------------------------------------------------
   u0    RAID-1    OK             -       -       -       232.82    ON     OFF
   u1    RAID-10   VERIFYING      -       37      64K     4656.51   ON     OFF
   u2    SPARE     VERIFYING      -       34      -       465.753   -      OFF
   u3    SPARE     OK             -       -       -       465.753   -      OFF


RAID Performance Tests with XFS


============================================================================
#write/#read    1/0             1/1             10/10           50/0            50/50
--------------------------------------------------------------------------------------
hwR10           350/0           135/78          56/38           130/0           46/34   (20 disks)
hwR1            80              50/25           13/6            22/0            0.1/24  ( 2 disks )

swR0hwR1        345/0           180/90          166/139         160/0           120/85  (20 disks)
swR0hwR5        320/0           158/91          103/78          100/0           93/68   (20 disks)


hwR10 = hardware R10                    (~ 5TB)
hwR1  = hardware R1                     (~ 5TB)
swR0hwR1 = software RAID0 on top of 10 hardware RAID1 (~ 5TB)
swR0hwR5 = software RAID0 on top of 4 hardware RAID5 (~ 7.8 TB)




Total Throughput Read 50M files - 2900 files in parallel

lustre_read_50M_3000.gif

lustre_read_50M_3000_cpu.gif

We get ~500 Mb/s over 12 hours stable. Few disk server become always hotspots. The disk i/o on all 25 machines is at 1 Gb/s while the network export is only 500 Mb/s. This is not
fully understood yet but it must be due to ineffective caching.

lustre_read.gif

I/O seen on a single disk server during the test


lxfsrc1204_0_0_NUMKBREADAVG_NUMKBWRITEAVGOVERLAYN_1.gif

lxfsrc1204_0_0_CPUUTILPERCUSER_CPUUTILPERCSYSTEM_CPUUTILPERCNICE_CPUUTILPERCIDLE_CPUUTILPERCIOWAIT_CPUUTILPERCIRQ_CPUUTILPERCSOFTIRQSTACKEDC_1.gif


Total Throughput read 500M files (290 clients)

Peak rate was 1.2. Gb, then decaying due to verify operation on two disk servers.
The default redahead for the 3ware controllers was '256'. In a seconde test run I have changed it to the recommended setting of '16384', the rate stays more stable.
wassh -t 10 -e lxb8971 -l root -c fileserver/dpm-test "blockdev --setra 16384 /dev/sdb"

Write Test with 8 Stripes

Writing 500 MB files with 8 stripes each. 290 clients. Peak performance shown in Lemon is 2.7 Gb/s. 29000 Files =~ 14.5 TB
write500-stripe8.gif

Test Setup with native /dev/sdb device (no loopback) and Raid10 (20 disks)

 wassh -l root -e "lxb8971" -c fileserver/dpm-test "mkfs.lustre --mkfsoption=\"-E stride=160 -i 1000000\" --param=\"failover.mode=failout\" --fsname tier2fs --ost --mgsnode=lxb8971@tcp0  --reformat /dev/sdb"
The setup without loopback devices improved drastically the performance.
This plot shows the write performance over the 24 disk server. The read performance looks very similiar ( - 10%)
lustre-read.jpg

This plot shows read and write in parallel. Lustre handles seems to provide a better balancing between read & write then the native device.

lustre-read-write.jpg

This plot shows xrootd running on top of the lustre cluster. We get identical performance to the native lustre.

xrootd-on-lustre-read.jpg




This plot summrarizes the performance of the different setups.

  1. xrootd native (read + write) [ read alone was 1.9 Gb/s - write 2.5 Gb/s]
  2. lustr native (write | read | read+write
  3. xrootd over lustre

xrootd-on-lustre-read-rate.jpg


gridFTP setup on Lustre

On a client machine where you mount the lustre FS install the lustre-gridftp script in /etc/init.d https://twiki.cern.ch/twiki/bin/viewfile/LCG/Scalability_Lustre?rev=1;filename=lustre-gsiftp and do
/etc/init.d/lustre-gridftp start (in the end this is just a stand gridftp server operating with file: dsi plugin). One get's around 90 Mb/s for a 1GB file with 16 parallel streams on the same network segment.


Performance test running CMS SuSY analysis via mounted LustreFS

The first 7 plots are realtime plots showing the load figures on client and server nodes. The last 7 plots are history plots and the test can be seen there from 11:00 ->11:20 (the last 20 minutes in the history).
We run 450 jobs on 360 cores (9 jobs per 8 cores) on 45 client hosts against 24 disk server. We get 1.7 GB/s total read rate. We have each client node ~ 80% CPU busy and 20% io wait.
These CMS jobs do about 4 MB/s i/o each reading 8 indivudal 1.1GB files sequential via the mounted LustreFS.


snapshot1.png

snapshot2.png


snapshot3.png

snapshot4.png


snapshot5.png

snapshot6.png

snapshot7.png

snapshot8.png

snapshot9.png

snapshot10.png


snapshot11.png

snapshot12.png


snapshot13.png


snapshot14.png


Setting up a Twin-LustreFS

The goal is to setup a redundant LustreFS which operates via xrootd like a network RAID-0.

Setup of Twin Lustre (all on single box)

  • create more loopback devices
    mknod -m 660 /dev/loop<dev#> b 7 <dev#>
    
  • create seperateMDS
    dd if=/dev/zero of=/scratch/twin/mds bs=1024 count=0 seek=8200
    mkfs.lustre --mgs --device-size=2000000 --reformat /scratch/twin/mds
    mkdir /mds
    mount -o loop -t lustre /scratch/twin/mds /mds
    
    
  • create two MDT
    dd if=/dev/zero of=/scratch/twin/mdt1 bs=1000 count=0 seek=200000000
    dd if=/dev/zero of=/scratch/twin/mdt2 bs=1000 count=0 seek=200000000
    mkfs.lustre --fsname=twin1 --mdt --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/mdt1
    mkfs.lustre --fsname=twin2 --mdt --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/mdt2
    mount -o loop -t lustre /scratch/twin/mdt1 /mdt1
    mount -o loop -t lustre /scratch/twin/mdt2 /mdt2
    
  • create two times two OSTs (we should add later also the failnode parameter see beginning of Twiki)
    dd if=/dev/zero of=/scratch/twin/ost11 bs=1000 count=0 seek=200000000
    dd if=/dev/zero of=/scratch/twin/ost12 bs=1000 count=0 seek=200000000
    dd if=/dev/zero of=/scratch/twin/ost21 bs=1000 count=0 seek=200000000
    dd if=/dev/zero of=/scratch/twin/ost22 bs=1000 count=0 seek=200000000
    mkfs.lustre --fsname twin1 --ost --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/ost11 
    mkfs.lustre --fsname twin1 --ost --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/ost12 
    mkfs.lustre --fsname twin2 --ost --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/ost21 
    mkfs.lustre --fsname twin2 --ost --mgsnode=pcitsmd01@tcp0 --backfstype=ldiskfs --device-size=2000000 --reformat /scratch/twin/ost22
    mount -o loop -t lustre /scratch/twin/ost11 /ost11
    mount -o loop -t lustre /scratch/twin/ost12 /ost12
    mount -o loop -t lustre /scratch/twin/ost21 /ost21
    mount -o loop -t lustre /scratch/twin/ost22 /ost22
    
  • mount the two Lustre-FS
    mount -t lustre -o user_xattr,acl pcitsmd01@tcp0:/twin1 /twin1
    mount -t lustre -o user_xattr,acl pcitsdm01@tcp0:/twin2 /twin2 
    

Recovery Procedures

Find all files on a OST

lfs df
=========================================================================
pcitsmd01] /home/alientest/xrootd-lustre > lfs df
UUID                 1K-blocks      Used Available  Use% Mounted on
twin1-MDT0000_UUID     1749776    185300   1564476   10% /twin1[MDT:0]
twin1-OST0000_UUID     1968528    586628   1381900   29% /twin1[OST:0]
twin1-OST0001_UUID     1968528    655548   1312980   33% /twin1[OST:1]

filesystem summary:    3937056   1242176   2694880   31% /twin1

UUID                 1K-blocks      Used Available  Use% Mounted on
twin2-MDT0000_UUID     1749776    183468   1566308   10% /twin2[MDT:0]
twin2-OST0000_UUID     1968528    604624   1363904   30% /twin2[OST:0]
twin2-OST0001_UUID     1968528    590440   1378088   29% /twin2[OST:1]

filesystem summary:    3937056   1195064   2741992   30% /twin2

lfs find -O twin1-OST0000_UUID /twin1
----> list of filenames 


Head Node Redunance

Using drbd for device replication

Download, compile, install as usual. 'modprobe drbd'
Example configuration to replicate the devices /dev/sdb1 + /dev/sdb2 between two head nodes

global {
  usage-count yes;
}
common {
  protocol C;
}

resource cms-xl-1 {
  on lxb8901.cern.ch {
    device    /dev/drbd1;
    disk      /dev/sdb1;
    address   128.142.209.49:7789;
    meta-disk /dev/sdb3[0];
  }
  on lxb8902.cern.ch {
    device    /dev/drbd1;
    disk      /dev/sdb1;
    address   128.142.209.50:7789;
    meta-disk /dev/sdb3[0];
  }
  syncer {
    rate 40M;
  }
}


resource cms-xl-2 {
  on lxb8901.cern.ch {
    device    /dev/drbd2;
    disk      /dev/sdb2;
    address   128.142.209.49:7790;
    meta-disk /dev/sdb4[0];
  }
  on lxb8902.cern.ch {
    device    /dev/drbd2;
    disk      /dev/sdb2;
    address   128.142.209.50:7790;
    meta-disk /dev/sdb4[0];
  }
  syncer {
    rate 40M;
  }
}

Create/Attach/Connect/Synchronize the drbd devices

Execute these commands on both hosts besides the 'primary' command.

drbdadm create-md cms-xl-1
drbdadm create-md cms-xl-2

drbdadm attach cms-xl-1
drbdadm attach cms-xl-2
drbdadm connect cms-xl-1
drbdadm connect cms-xl-2
drbdadm -- --overwrite-data-of-peer primary cms-xl-1 # only on primary node
drbdadm -- --overwrite-data-of-peer primary cms-xl-2 # only on primary node

cat /proc/drbd
version: 8.2.5 (api:88/proto:86-88)
GIT-hash: 9faf052fdae5ef0c61b4d03890e2d2eab550610c build by root@lxb8901.cern.ch, 2008-04-25 12:03:43

 1: cs:Connected st:Primary/Secondary ds:UpToDate/UpToDate C r---
    ns:7823623 nr:0 dw:0 dr:7823623 al:0 bm:478 lo:0 pe:0 ua:0 ap:0
        resync: used:0/31 hits:488500 misses:478 starving:0 dirty:0 changed:478
        act_log: used:0/257 hits:0 misses:0 starving:0 dirty:0 changed:0
 2: cs:Connected st:Secondary/Secondary ds:Inconsistent/Inconsistent C r---
    ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0
        resync: used:0/31 hits:0 misses:0 starving:0 dirty:0 changed:0
        act_log: used:0/257 hits:0 misses:0 starving:0 dirty:0 changed:0



When devices are synced, create the needed filesystem on the primary. Mount the device only on the primary!

Dealing with Split-Brain Situation

If a device has been mounted on two nodes, a split brain is detected and drbd will refuse to collaborate.
You have to declare one node as secondary and discard changes on the secondary node by issuing:
drbdadm secondary mdscern 
rbdadm -- --discard-my-data connect mdscern

Tuning Lustre for mgs failover node

tunefs.lustre --erase-params --mgsnode=128.142.167.202@tcp --mgsnode=128.142.167.201@tcp0 --param "failover.node=128.142.167.201" --param "mdt.quota_type=ug" --writeconf  /dev/drbd4

IPMI Control

For HA configuration we need IPMI configuration to be able to power-cycle machines.
ipmitool -I open chassis status # see the status of a chassis
ipmitool -I open user list # see the configured users
ipmitool -I open user set name 6 lustreha # set a new user name for id 6
ipmitool -I open user set password 6 # set the password for user 6 in interactive mode
ipmitool user enable 6
ipmitool user priv 6 4 1 # set user prviviledges for channel one to administrator!
IPMI_PASSWORD=<your password here> <cmd> # to set the password from an application!
ipmitool -U lustreha -I lan -H x.x.x.x -E chassis power status #connect from another node !!! You have to use the IPMI address which you can find out with ipmitool -I open lan print

Building Heartbeat


wget http://linux-ha.org/download/heartbeat-2.1.3-1.fc7.src.rpm 
rpm -i heartbeat-2.1.3-1.fc7.src.rpm 
yum install libnet
rpmbuild -bb /usr/src/redhat/SPECS/heartbeat.spec

Testing failover:

/usr/lib64/heartbeat/hb_takeover local

-- AndreasPeters - 03 Mar 2008

  • lustre-gsiftp: init.d script to startup a gridftp server on a lustre client
Topic attachments
I Attachment History Action Size Date Who Comment
Unix shell scriptsh create_raid_and_xfs.sh r1 manage 3.1 K 2008-05-05 - 11:04 AndreasPeters 3-ware RAID scripts
Unknown file formatrpm e2fsprogs-1.40.4-0.x86_64.rpm r1 manage 999.2 K 2008-05-08 - 14:44 AndreasPeters e2fsprogs with Lustre patches
Unknown file formatrpm kernel-module-openafs-2.6.9-67.0.7.EL.lustresmp-1.4.4-5.cern.x86_64.rpm r1 manage 3525.8 K 2008-04-30 - 17:15 AndreasPeters OpenAFS Kernel Module for CERN kernel with Lustre patch
Unknown file formatrpm kernel-smp-2.6.9-67.0.7.EL.lustre.x86_64.rpm r1 manage 12436.6 K 2008-04-30 - 16:48 AndreasPeters CERN SMP Kernel with Lustre patches
Unknown file formatrpm lustre-1.6.4.3-2.6.9_67.0.7.EL.lustresmp_200804301338.x86_64.rpm r1 manage 3778.3 K 2008-04-30 - 16:49 AndreasPeters Lustre 1.6.4.3 tools for patched CERN SMP Kernel
Unknown file formatext lustre-gsiftp r1 manage 2.5 K 2008-03-13 - 11:58 AndreasPeters init.d script to startup a gridftp server on a lustre client
Unknown file formatrpm lustre-ldiskfs-3.0.4-2.6.9_67.0.7.EL.lustresmp_200804301338.x86_64.rpm r1 manage 827.0 K 2008-04-30 - 16:50 AndreasPeters Lustre 1.6.4.3 ldiskfs module for patched CERN SMP Kernel
Unknown file formatrpm lustre-modules-1.6.4.3-2.6.9_67.0.7.EL.lustresmp_200804301338.x86_64.rpm r1 manage 14052.0 K 2008-04-30 - 16:50 AndreasPeters Lustre 1.6.4.3 kernel modules for patched CERN SMP Kernel
JPEGjpg lustre-read-write.jpg r1 manage 66.9 K 2008-03-11 - 18:45 AndreasPeters  
JPEGjpg lustre-read.jpg r1 manage 61.3 K 2008-03-11 - 18:44 AndreasPeters  
JPEGjpg lustre-read2.jpg r1 manage 49.4 K 2008-03-11 - 18:44 AndreasPeters  
GIFgif lustre_read.gif r1 manage 8.3 K 2008-03-07 - 11:16 AndreasPeters  
GIFgif lustre_read_50M_3000.gif r1 manage 16.9 K 2008-03-07 - 11:01 AndreasPeters  
GIFgif lustre_read_50M_3000_cpu.gif r1 manage 19.5 K 2008-03-07 - 11:01 AndreasPeters  
GIFgif lustrewrite50.gif r1 manage 12.5 K 2008-03-06 - 18:16 AndreasPeters  
JPEGjpg lustrewrite50.jpg r1 manage 20.8 K 2008-03-06 - 18:21 AndreasPeters  
GIFgif lxfsrc1204_0_0_CPUUTILPERCUSER_CPUUTILPERCSYSTEM_CPUUTILPERCNICE_CPUUTILPERCIDLE_CPUUTILPERCIOWAIT_CPUUTILPERCIRQ_CPUUTILPERCSOFTIRQSTACKEDC_1.gif r1 manage 20.7 K 2008-03-07 - 11:04 AndreasPeters  
GIFgif lxfsrc1204_0_0_NUMKBREADAVG_NUMKBWRITEAVGOVERLAYN_1.gif r1 manage 15.6 K 2008-03-07 - 11:04 AndreasPeters  
JPEGjpg read-cpu-iowait.jpg r1 manage 55.4 K 2008-03-11 - 18:44 AndreasPeters  
PNGpng snapshot1.png r1 manage 24.7 K 2008-03-14 - 11:43 AndreasPeters  
PNGpng snapshot10.png r1 manage 43.7 K 2008-03-14 - 11:46 AndreasPeters  
PNGpng snapshot11.png r1 manage 156.5 K 2008-03-14 - 11:52 AndreasPeters  
PNGpng snapshot12.png r1 manage 96.9 K 2008-03-14 - 11:52 AndreasPeters  
PNGpng snapshot13.png r1 manage 158.3 K 2008-03-14 - 11:52 AndreasPeters  
PNGpng snapshot14.png r1 manage 18.8 K 2008-03-14 - 11:52 AndreasPeters  
PNGpng snapshot2.png r1 manage 24.9 K 2008-03-14 - 11:43 AndreasPeters  
PNGpng snapshot3.png r1 manage 20.8 K 2008-03-14 - 11:43 AndreasPeters  
PNGpng snapshot4.png r1 manage 19.1 K 2008-03-14 - 11:44 AndreasPeters  
PNGpng snapshot5.png r1 manage 23.0 K 2008-03-14 - 11:44 AndreasPeters  
PNGpng snapshot6.png r1 manage 122.7 K 2008-03-14 - 11:45 AndreasPeters  
PNGpng snapshot7.png r1 manage 108.8 K 2008-03-14 - 11:45 AndreasPeters  
PNGpng snapshot8.png r1 manage 138.0 K 2008-03-14 - 11:45 AndreasPeters  
PNGpng snapshot9.png r1 manage 65.7 K 2008-03-14 - 11:45 AndreasPeters  
GIFgif write500-stripe8.gif r1 manage 9.4 K 2008-03-10 - 11:03 AndreasPeters  
JPEGjpg xrootd-290-1500-clients-read.jpg r1 manage 44.8 K 2008-03-12 - 13:50 AndreasPeters  
JPEGjpg xrootd-on-lustre-read-rate.jpg r1 manage 60.6 K 2008-03-11 - 18:48 AndreasPeters  
JPEGjpg xrootd-on-lustre-read.jpg r1 manage 61.5 K 2008-03-11 - 18:47 AndreasPeters  
Edit | Attach | Watch | Print version | History: r31 < r30 < r29 < r28 < r27 | Backlinks | Raw View | WYSIWYG | More topic actions
Topic revision: r31 - 2008-06-04 - AndreasPeters
 
    • Cern Search Icon Cern Search
    • TWiki Search Icon TWiki Search
    • Google Search Icon Google Search

    LCG All webs login

This site is powered by the TWiki collaboration platform Powered by PerlCopyright & 2008-2020 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback